Were you searching for resources around Installing A Bathtub?
Mounting a tub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the task can move speedily; if you need to open up a wall to remove the old bathtub and place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to vacate the old tub as well as set in the brand-new one. See to it you have actually certified yourself for the work and fit trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to think about employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will help you mount a brand-new bathtub in your shower room if you have actually already acquired a new tub as well as do not require to alter the setup of your previous water system pipelines.
Your devices as well as material checklist should consist of the following:
Preparing for the Installment
Firstly, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before going on to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the tub in the called for placement. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages and tighten them if needed. Fill the tub and also examine the overflow outlet as well as the normal outlet for leaks.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been made use of at least once as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washers remain in location in between the tap and the sink. Protect the tap in position with the maker offered backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The previous type ought to be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split a stiff seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that excerpt was worth the trouble. Those who liked our post please be sure to share it. Thank-you for going through it.
We're here for you, dial!